This system combines the results got with a closed enclosure and those obtained with a labyrinth and folded pavilion.
It is indeed recognized that a closed chamber has many advantages for the damping of the speaker, so its transient response, provided you have a very flexible speaker and strong magnetic field. However, the resonance frequency of the speaker in an enclosed cabinet (of reasonable size) significantly increases and the acoustic performance below that frequency decreases very rapidly to 6 dB per octave. On the other hand, the back wave is lost. The efficiency of such a speaker is in any case 6 dB lower than a system that recovers the rear wave.
The Infinite acoustic line system is to use the rear wave. It is "forced" in a labyrinth tapered whose length is at least equal to 1.50 m
The labyrinth is folded so as to collect the back wave in phase* with the front wave to enhance performance in the bass and sub-bass...
Then The originality of the system resides in an internal acoustic filter which acts as a "low-pass" for the rear wave and "high-pass" for the front wave, the assembly acting as two loudspeakers coupled without delay (unlike the passive-active system).
The speaker A (front wave) sees its sound pressure decreases by 6 dB per octave from the resonance frequency of the speaker in the enclosure (70 Hz to 100 Hz depending on the speakers) and the speaker B (rear wave) sees his sound pressure almost constant of 30 Hz to 70 Hz or 100 Hz to decrease above 100 Hz.
The combination of the two waves in phase gives a perfectly linear reproduction from 30 Hz.
(*) Rigorous phasing is obtained by a progressive damping of the rear wave through increasing density absorbent.
The careful calculation of absorbent densities allows to artificially lengthen the path of the rear wave up to 3 times the geometrical length of a constant section pipe.
• Input impedance : 6 Ω
• Rated power : 60 W
• Maximum power : 75 W
• Sensitivity (for 1 W at 1 m) : 90 dB
• Amplitude frequency response curve : 20 to 35 000 Hz
• Bandwidth (±3 dB) : 40 to 30 000 Hz
• Cutoff frequencies : 400 - 4000 Hz
- Tweeter : dome 19 mm ITT - LPKH90-19-145FK
Dôme Mylar
Aimant clos
Caractéristiques
Unités
Valeurs
Puissance nominale
W
30
Puissance maximale
W
50
Bande passante
Hz
4000-25000
Niveau d'efficacité caractéristique
dB
90
Diamètre nominal hors tout
mm
118
Diamètre bobine mobile
mm
19
Diamètre ouverture baffle
mm
75
Introduction dans l'entrefer
gauss
14500
Flux dans l'entrefer
Maxwells
-
Énergie magnétique du moteur
WS-1
-
Facteur de force
NA-1
-
Hauteur du bobinage
mm
-
Hauteur de l'entrefer
mm
-
Masse de l'aimant
g
-
Masse équipage mobile
g
-
Masse du haut parleur
g
400
Impédance nominale
Ω
8
Fréquence de résonance
Hz
1500
Facteur de qualité mécanique
Qms
-
Facteur de qualité électrique
Qes
-
Facteur de qualité total
Qts
-
Compliance de la suspension
10-3 MN-1
-
Température max de bobine mobile
C
-
- Midrange : dome 50 mm 3A - DS50
Caractéristiques
Unités
Valeurs
Puissance nominale
W
50
Puissance maximale
W
120
Bande passante
Hz
700-6000
Niveau d'efficacité caractéristique
dB
90
Diamètre nominal hors tout
mm
160
Diamètre bobine mobile
mm
50
Diamètre ouverture baffle
mm
125
Introduction dans l'entrefer
gauss
12 600
Flux dans l'entrefer
Maxwells
28 000
Énergie magnétique du moteur
WS-1
0,657
Facteur de force
NA-1
7,9
Hauteur du bobinage
mm
4
Hauteur de l'entrefer
mm
5
Masse de l'aimant
g
850
Masse équipage mobile
g
3,2
Masse du haut parleur
g
1 960
Impédance nominale
Ω
8
Fréquence de résonance
Hz
380
Facteur de qualité mécanique
Qms
5,1
Facteur de qualité électrique
Qes
1,7
Facteur de qualité total
Qts
0,57
Compliance de la suspension
10-3 MN-1
-
Température max de bobine mobile
C
180
- Boomer : 27 cm 3A - W100
Caractéristiques
Unités
Valeurs
Puissance nominale
W
100
Puissance maximale
W
120
Bande passante
Hz
-
Niveau d'efficacité caractéristique
dB
-
Diamètre nominal hors tout
mm
295
Diamètre bobine mobile
mm
50
Diamètre ouverture baffle
mm
234
introduction dans l'entrefer
gauss
-
Flux dans l'entrefer
Maxwells
-
Energie magnétique du moteur
WS-1
-
Facteur de force
NA-1
-
Hauteur du bobinage
mm
-
Hauteur de l'entrefer
mm
-
Masse de l'aimant
g
-
Masse équipage mobile
g
-
Masse du haut parleur
g
3100
Impédance nominale
Ω
8
Fréquence de résonance
Hz
-
Facteur de qualité mécanique
Qms
-
Facteur de qualité électrique
Qes
-
Facteur de qualité total
Qts
-
Compliance de la suspension
10-3 MN-1
-
Température max de bobine mobile
C
-
• Dimensions (H x W x D) : 78 x 32 x 30 cm
• Acoustic volume : 55 dm3
• Unit weight : 24 kg
Speakers to place on the floor only.
"Presence" setting of the midrange register by 4 positions switch on the front.
• 1 : -4 dB Low level listening • 2 : -2 dB Midrange set back • 3 : Linear • 4 : +2 dB midrange set front